JUPITER Benelux · +31 182 399 837 · info@jupiter.nl
NLENFRDE
Home › Dry screed › NORIT-TE 15
NORIT-TE 15 gypsum fibre screed board
Corridor in a renovated office building with a NORIT dry floorFinished interior with a wooden floor on a NORIT dry floor
NORITDry screed · Lindner

NORIT-TE 15 gypsum fibre dry floor

A 15 mm gypsum fibre screed board, made by Lindner in Germany. With the push-fit joint and NORIT-TE adhesive you lay the boards without screws or staples. Together they form a load-distributing layer under all common floor finishes.

  • 1200 × 600 × 15 mm
  • 0.72 m² per board
  • Fire class A1
  • Wet rooms up to W1-I
Order in the JUPITER ShopAsk for advice

Delivery through the JUPITER Shop, also on a business account

What is NORIT-TE 15 suitable for?

  • As a load-distributing screed under all common floor finishes.
  • The thinnest board in the NORIT screed range: 15 mm.
  • Wet rooms up to water exposure class W1-I according to DIN 18534, such as a bathroom floor in a home, with suitable waterproofing.
  • With underfloor heating: as a screed on a dry-build underfloor heating system such as JUPITER IDEAL. Ask for advice on the build-up.
Not suitable for

Floors with a floor drain or channel, such as a walk-in shower (class W2-I and higher). For heavy or concentrated loads: ask for advice first.

Technical data

Format1200 × 600 mm
Thickness15 mm
Coverage per board0.72 m²
Weightapprox. 14.1 kg per board (approx. 19.6 kg/m²)
Densityapprox. 1,250 kg/m³
MaterialGypsum fibre
JointPush-fit joint, glued with NORIT-TE adhesive (solvent-free PU adhesive, open time approx. 30 min at 20 °C)
Fire classA1, non-combustible (EN 13501-1)
Product standardEN 14190
Wet roomsWater exposure class W0-I and W1-I
Packaging80 boards per pallet (approx. 1,140 kg, 57.6 m²)

Source: Lindner product data sheet NORIT-TE 15 (DB_N_TE_15/EN/1.0). Sound insulation and fire resistance depend on the complete floor build-up and are therefore not listed in this table; ask for advice on your build-up.

Accessories

NORIT-TE adhesive
1 kg bottle for approx. 40 m², in the JUPITER Shop
Tapping block
For installing TE elements, in the JUPITER Shop

Installation

Tools: hand-held circular saw with guide rail for straight cuts, jigsaw for curves and cut-outs, NORIT-TE adhesive.

  1. 1Let the boards acclimatise on site for 2 days and fit edge insulation along all walls: PE foam, stone wool or an alternative, depending on the requirements.
  2. 2Apply NORIT-TE adhesive in the groove. At 20 °C the adhesive remains workable for about 30 minutes.
  3. 3Push the next board into the previous one and close the joints.
  4. 4Cut the fitting boards to size and finish the edges.
  5. 5Apply the floor finish according to the installation guidelines and in line with the wishes and requirements of the floor finish supplier.
How many boards do you need?

Including approx. 10 % cutting waste: area × 1.1 ÷ 0.72.

Area in m²
62boards NORIT-TE 15

Fits on 1 pallet (80 boards per pallet)

  • Edge insulationapprox. 40 m
  • NORIT-TE adhesive, 1 kg bottleapprox. 1 bottle

Averages: approx. 1 m of edge insulation per m² and 1 bottle of adhesive per approx. 40 m². The actual quantity depends on the shape of the room.

Order in the JUPITER Shop

What do you save without screws or staples?

You glue NORIT-TE boards and click or push them together. A common screwed gypsum fibre screed system adds approx. 15 screws or approx. 19 staples per m². Work out for yourself what that saves in your project.

Less work, only gypsum fibre in the floor

No screws or staples. You do not need to buy, count or drive them.

Less finishing work. According to Lindner, there is less filling and rework before the floor finish goes on.

No metal in the floor. If the floor is sawn or milled later, the tools do not hit any screws or staples. The floor contains only gypsum fibre boards and cured adhesive: PU adhesive (NORIT-TE adhesive) or PVAc adhesive.

Check it with your own figures

Enter your own time per screw or staple and your hourly rate. We do not fill these in for you.

Area in m²
Time per screw or staple, in seconds
Extra finishing work per m², in minutes (optional)
Hourly rate in euros
600fewer screws

or approx. 760 staples

  • Labour time–
  • Labour costs–

Enter your time per screw or staple and your hourly rate.

Indication based on your own input. Quantities according to the installation guidelines of a common screwed gypsum fibre screed system: approx. 15 screws (spacing max. 20 cm) or approx. 19 staples (max. 15 cm) per m². Material costs for screws and staples are not included.

Downloads

Goes with

NORIT-TE 20 →20 mm · click jointNORIT-TE 25 →25 mm · click jointNORIT dry fill →expanded clay · 15–100 mm

Accessories in the JUPITER Shop:NORIT-TE adhesive (1 kg bottle for approx. 40 m²) · Tapping block

Not sure about the build-up?

About the subfloor, wet rooms or underfloor heating: JUPITER Benelux is happy to advise. Weekdays 08:00–17:00 (CET).

Request advice or a quoteCall +31 182 399 837